How many kinds of module Construction?

 

Precautions For Handling LCD Modules

 

LCMs have been assembled and adjusted before delivery; therefore, observe the following procedures for handling:
Warning For Static Electricity

LCMs use CMOS LSI. Therefore, measures to protect static electricity have been taken through all the processes from manufacturing to shipping. When handling, take necessary care to prevent static electricity as you would any CMOS IC.

Do not take LCM from its anti-static bag until it is time to assemble:

LCMs are individually packaged in bags treated to resist static electricity. An LCM should not be removed from the bag until it is time to solder the terminals. When storing the LCMs keep them packaged in the anti-static bags, or a container that is resistant to static electricity, or in an electric conductive container.

Always use a body ground when handing an LCM:

Always apply grounding to your body while you are working with an LCM from the time it is taken out of the anti-static bag until it is assembled. When it is necessary to handle the LCM, once it is taken out of the bag, always place it in a electric conductive container. Avoid wearing clothes of chemical fiber. Cotton or conductive treated fiber clothes are recommended.

Use a no-leak soldering iron:

The soldering iron used for soldering the I/ O terminals of the LCM should be insulated at the iron tip or grounded on the iron tip.

An electrical apparatus is always required for assembly:

When the LCM is to be assembled with an electrical apparatus, this assembly should be grounded to avoid transmitting spike noise generated with the motor rotating.

Make the operation bench equal to the ground

When the operation bench is grounded with an aluminum or steel plate, there is always the possibility of an electric shock being generated, when the impedance is too low. It is therefore recommended that an electric conductive (rubber) mat be used.

Peel off the LCM protective film slowly:

To the face of the LCM is a film to protect the display surface from contamination, flaw, adhesion of flux, etc. Peeling off this film too abruptly may cause static electricity to be generated. Thus peel off the tape slowly.

Attention should be paid to humidity:

50~60%RH is acceptable.

 

Precautions For Soldering The LCM

 

The following procedures should be followed when soldering the LCM:

Solder is to be applied only to the I / O terminals.

Use a soldering iron with no leakage.

In addition, further attention should be paid to the following.

Conditions for soldering I / O terminals:

Temperature at iron tip: 280 o C + 10 o C

Soldering time: 3-4 sec. / terminal

Type of solder: Eutectic solder ( rosin flux filled )

Avoid using flux, since it may penetrate the LCM and could possibly cause contamination.

When cleaning is required do not remove the protective film until after soldering the I / O terminals has been completed.This will eliminate contamination with by the dispersion of flux where soldering.

Removing the wiring:

When a lead wire or a connector that has been soldered to the I / O terminals of the LCM is to be removed ,do so only after the solder at the connection has sufficiently melted. If this wire or connector is forcefully removed, it may cause the terminal to break or peel. It is recommended that a suction-type soldering iron be used. Do not attempt to solder a lead wire or connector more than 3 times to a given LCM.

Excess Current Protection

An over current protection circuit is not provided with the LCM. Therefore, it is recommended to use an electrical source which will provide for this current protection.

Long-Term Storage

When long-term storage of an LCM is necessary, the following procedures should be complied with: If not stored properly, it could cause deterioration of the polarizer and oxidation of the I/O terminals that would make soldering more difficult.

1. Store in original packaging if possible.

2. For individual LCMs, place them in anti-static bags, sealing the opening and storing it where it is not subject to direct sunlight or the light from a fluorescent light.

3. Store in a temperature range of 0oC ~35oC with low humidity. Note, refer to the specific module specification for requirements regarding storage temperature and humidity.

 

Copyright © 2010 ONVISION LCD, All rights Reserved.
More infomations, Please visit http://www.onvision-lcd.com